CAN I INSTALL A BATHTUB MYSELF?

Can I Install A Bathtub Myself?

Can I Install A Bathtub Myself?

Blog Article

Request An Estimate

Right here below you can locate a lot of very good material with regards to How to Install a Bathtub.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Setting up a bath tub isn't precisely rocket science, however it does call for solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily available, the task can move quickly; if you need to open up a wall to eliminate the old tub as well as place the new tub, the task is much harder. In either instance, the project is within a house handyman's skills, although you will require a helper to leave the old bathtub and embeded in the brand-new one. See to it you have certified on your own for the task and also are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration employing one before you begin. Possibilities are you might need an expert plumber to make tube links.
This write-up will assist you set up a brand-new tub in your washroom if you have already bought a new tub and don't need to alter the plan of your previous water system pipelines.
Your devices and also product list need to comprise the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Getting ready for the Installation


    Firstly, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the producer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets unit to avoid strain on the bathtub.
    Fit the adaptable tap connectors to the bottom of both faucets utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
    Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its final position.

    Removing Old Taps


    If you need to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is detach the water. After doing so, activate the taps to drain any type of water continuing to be in the system. The process of removing the existing taps can be rather bothersome as a result of the restricted access that is usually the case.
    Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly come from the pipes. As soon as the supply pipelines have been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this process. When the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned of any type of old sealing compound.
    Prior to proceeding to fit the brand-new taps, compare the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.

    Mounting the Bath tub


    Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wood boards are useful in equally spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
    The next objective is to ensure that the tub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the bathtub up until the level reads level.
    To mount taps, fit the bottom of the outermost flexible tap adapter to the appropriate supply pipeline by making a compression join; then do the very same for the other tap.
    Activate the water supply and inspect all joints and also brand-new pipework for leaks as well as tighten them if required. Load the bathtub and likewise examine the overflow outlet and the typical electrical outlet for leakages.
    Ultimately, fix the bath paneling as described in the maker's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has actually been made use of a minimum of once as this will certainly settle it into its last setting.

    Suitable New Touches


    If the tails of the new taps are plastic, then you will require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
    If you require to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
    Next off, place the faucet in the placing opening in the bath/basin making certain that the washers are in place in between the faucet and also the sink. Safeguard the faucet in position with the maker supplied backnut. When the tap is safely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal tap adapters. The previous kind needs to be attached to the faucet ends first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Bathtub


    In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture a rigid seal, creating the water to pass through the wall surface between the bath and the tiling, bring about complications with moisture and feasible leakages to the ceiling below.
    You can select from a variety of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, as well as are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to permit the activity experienced when the bathtub remains in use. The sealer can fracture relatively early if you do not take into account this motion before sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly readily available on the marketplace. It is a good idea to fit the tiles utilizing waterproof or water resistant glue and grout.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    How to Install a Bathtub

    I hope you enjoyed our excerpt on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you for taking a few minutes to read through our piece. Feel free to take the opportunity to distribute this article if you liked it. Thanks so much for your time invested reading it.




    Quote & Schedule


    Report this page